- Coolterm data log to excel how to#
- Coolterm data log to excel install#
- Coolterm data log to excel serial#
- Coolterm data log to excel software#
Open the capture file in Notepad (or another text editor) and you should see lines that look just like what you saw in the terminal window. When you have collected some data, click the “Stop Capture” button to end the capture process. If you get stuck, post in the support forum.Ĭlick “Start Overwrite” and the lower portion of the window will turn red to tell you that a capture operation is in progress. The steps for other terminal programs will be different. The default file path is probably fine for now. To actually save (or log) some data, click on the Capture tab. The data should look like this (the numbers may be different): CPS, 2, CPM, 15, uSv/hr, 0.08, SLOWĬPS, 0, CPM, 16, uSv/hr, 0.09, SLOW Step 5: Log some data These are RealTerm’s way of showing you the line endings – other terminal programs will probably not have these characters (and they can be turned off in RealTerm if you don’t like them). You might notice some funny characters at the end of each line (CRLF).
You should see the welcome message Geiger Counter 1.00Īnd lines of data should start appearing approximately once a second, as shown below: Your RealTerm settings should look like this when you’re done (click for a larger version):įlip on the power switch for your Geiger Counter kit. Click “Open”, or if Open is already selected, click “Change”.
Coolterm data log to excel software#
Coolterm data log to excel serial#
Don’t worry, this is actually pretty simple: You want to select the serial port number or name corresponding to the FTDI cable (port number 22, in my case), and configure the port as follows: In the RealTerm window, click on the “Port” tab and you’ll be confronted with a number of options. If you’re using another serial program (or another operating system), the procedure will be slightly different, but the settings are the same.
Coolterm data log to excel how to#
I’m going to show how to do this in RealTerm. Now it’s time to configure your serial program. If you are using RealTerm on Windows, you’ll see a window like this pop up: Launch the serial terminal program you installed in step 1. If you are using the FTDI Friend, match the writing on the silkscreen of the FTDI Friend to the labels on the Geiger Counter – BLACK goes towards blk, GREEN towards grn. The connector should be oriented such that the black wire is closest to the “blk” silkscreen label on the PCB, and the green wire closest to the “grn” label. Next, connect the FTDI cable to your Geiger Counter kit, as shown.
Coolterm data log to excel install#
If you haven’t already, plug your USB-serial cable into a free USB port on your computer (and install the USB drivers as detailed in step 1). Step 2: Connect the USB-Serial cable to your Geiger Counter You will also want to figure out what port number or device name corresponds to your USB-serial cable. If you are using Windows 7 or Linux, you may not need to install any drivers at all – they are included with your operating system. The drivers for the FTDI cable (and FTDI Friend) are available here and instructions for installing them are here. Consult the manufacturers’ website for more information. Next, install the drivers for your USB-serial cable. If you are using Ubuntu, CuteCom is available in the Ubuntu Software Center. Instructions are included with each of the programs listed above. Install the serial terminal program for your operating system. A serial terminal program for your operating system:.You can also use the slightly less expensive FTDI Friend, also available from Adafruit.Beware, the FTDI cable works well for this but many others do not! The cable must operate with a TTL logic level ‘high’ voltage around 3V.
I recommend the FTDI TTL-232R-3V3, available from many electronics suppliers, such as Adafruit Industries.A MightyOhm Geiger Counter Kit – available on this site or from one of my distributors.So, you want to log data with your Geiger Counter kit?
0 kommentar(er)
